|
|
|
MM-6795C
256MB
VME/VME64 Non-Volatile FLASH or NVRAM Memory
Module |
| Features |
|
Capacity
CMOS NVRAM: 16, 32, 64MB
Flash Memory: 32, 64, 128, 256MB |
|
On-board
timer provides 1 usec to 16 msec in
1 usec increments for Flash timing
requirements |
|
Compatible
with VME/VME64
A32/A24/D64/D32/D16/D8 (UAT) (BLT)
(MBLT) |
|
Data
retention for CMOS, 3 years with
lithium batteries, 4 weeks with
rechargeable NiCad batteries |
|
Cycle/Access Time CMOS NVRAM:
150/100 nsec Flash memory: 200/150
nsec (read only mode) |
|
Block
Transfer of 256 bytes for VME and
2KB for VME64 |
|
Two
on-board, redundant, fused lithium
or NiCad batteries |
|
Module
Selection on 1MB boundaries,
switch-selectable |
|
|
|
Description |
|
A high-speed, high density memory
module, the MM-6795C/F provides up to 64MB of
CMOS NVRAM or 128MB of FLASH memory on one
board. The MM-6795C/F is VME/VME64 bus
compatible. Boards operate with block transfer
(BLT) of 256 bytes for VME and 2KB for VME64
(MBLT). A FLASH memory
software driver example is provided on a floppy
diskette along with a sample listing in "C"
code. Software drivers for different operating
systems are also available.
With CMOS NVRAM, the MM-6795C
has three on-board, redundant, fused batteries
to retain memory in the event of power loss.
Batteries may be either rechargeable NiCad or
non-rechargeable lithium types. On-board LED's
and a control status indicate battery condition.
Reliability is ensured by
burn-in and running memory diagnostics that
check operation for 48 hours while
temperature-cycling boards from 0 - 60°C. |
|
MM-6795C
Specifications |
 |
Capacity : CMOS NVRAM: 16, 32, 64MB, Flash Memory:
32, 64, 128MB |
|
|
Cycle/Access Time : CMOS Static RAM: 150/100 nsec
(adjustable), Flash Memory: 150/100 nsec (adjustable) |
|
|
Address : 32-bits plus a 6-bit memory address
modifier |
|
|
Data In/Data Out : 8, 16, 32, 64 bits (UAT) and block
transfer (BLT) of 256 bytes for VME, and 2KB for VME64
(MBLT) |
|
|
Modes of Operation : Read, write, read-modify-write |
|
|
Module Selection : 1MB boundaries, switch selectable |
|
|
Interface : VME/VME64 |
|
|
On-Board Batteries : Three redundant, fused lithium
or NiCad batteries; each NiCad battery has its own charger.
Each battery type has a voltage monitor and LEDs to indicate
battery status. |
|
|
Battery Types : NiCad (rechargeable) Rating: 100 mA/hr
each, 3.6V
Data retention: 4 weeks, Lithium (non-rechargeable) Rating:
1500 mA/hr each, 3.6V, Data retention: 3 years |
|
|
Operating Temperature : 0 to +70°,C |
|
|
Storage Temperature : -40 to +85°,C Relative |
|
|
Relative Humidity : Up to 95% without condensation |
|
|
Flash Programming Power Requirements : +12V Vpp
switchable under software control |
|
|
Operating Power Requirements : +5V (fully pop.)
Standby 1.6A Operate 1.8A, +12V (programming) Operate 5mA |
|
|
